Welcome to Würth Mongolia For trade customers only

Adhesive lubricant HHS® foodstuffs

Foodsafe lubricant HHS NSF
LUB-FDSAVE-(FDGRD-HHS)-500ML
HHS

Art.-no. 08931076
EAN 4062856331130

Prices for customers after login
Adhesive lubricant HHS® foodstuffs

Art.-no. 08931076

Prices for customers after login
Quantity
PU

Exclusively for trade customers

Register now and access more than 125,000 products

Waterproof, synthetic adhesive lubricant with penetrating properties

Can be used in areas in which food is processed or stored


NSF H1-registered. The product may come into contact with foodstuffs for technical reasons.



Excellent penetrating properties


  • For lubrication in hard-to-reach places

  • Penetrates very tight spaces and tolerances


Good adhesive properties


  • Broad application range, e.g. on vertical lubrication points

  • Resistant to centrifugal forces on turning and rotating parts


Provides lasting protection against corrosion and non-ferrous metal corrosion



Waterproof



Resin-free and acid-free



Silicone-free and AOX-free

Notice

If used in areas in which food is processed or stored, only the minimum quantity technically necessary may be used. When using as an anti-corrosive film for food contact surfaces, completely remove all lubricant before re-starting the device.

NSF H1-registered (no.: 140816), meets the requirements of H1, 1998.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Datasheets(X)

Certificates/ Documents

 | 

 | 

Application area

Suitable for universal lubrication at high pressure loads, e.g. for chains, racks, joints, levers, bearings, sliding points, cables, open drives, and hinges.

Instructions

Shake can well before use. Thoroughly clean the lubricating point and then apply where required.

Chemical basis

Synthetic oil with a multifunction additive combination

Colour

Colourless

Smell/fragrance

Characteristic

Density

0.8 g/cm³

Density conditions

at 20°C

Min. temperature conditions

-25 °C

Max. temperature conditions

180 °C

Min. flashing point

200 °C

Kinematic oil basis viscosity

1251 mm²/s

Conditions for viscosity of oil basis

after evaporation of solvent at 40°C

Silicone-free

Yes

Acid-free

Yes

Resin-free

Yes

AOX-free

Yes

Resistance against

Water

Contents

500 ml

Container

Aerosol can

Shelf life from production

24 Month

Suitable glove:
 
Product
Description
Nitrile chemical protective glove With cotton velour finish inside
Nitrile chemical protective glove With cotton velour finish inside
Description:
Permeation level: 6
Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.
Measured breakthrough time
Permeation level
< 10 min
0
≥ 10 min
1
≥ 30 min
2
≥ 60 min
3
≥ 120 min
4
≥ 240 min
5
≥ 480 min
6

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information