HSCo8 AlCrN annular cutter - CREDRL-MET-HSCO8-ALCRN-DRLDP55MM-D40MM

HSCo8 AlCrN annular cutter - CREDRL-MET-HSCO8-ALCRN-DRLDP55MM-D40MM - 1

HSCo8 AlCrN annular cutter - CREDRL-MET-HSCO8-ALCRN-DRLDP55MM-D40MM - 2

HSCo8 AlCrN annular cutter - CREDRL-MET-HSCO8-ALCRN-DRLDP55MM-D40MM - 3

HSCo8 AlCrN annular cutter

Name: HSCo8 AlCrN annular cutter
Brand: Würth
SKU: 0630942640

Core drill bit HSCo8 AlCrN coating
CREDRL-MET-HSCO8-ALCRN-DRLDP55MM-D40MM
ZEBRA

Art.-no. 0630942640

EAN 4062856044917

All versions

Similar products

Prices for customers after login

HSCo8 AlCrN annular cutter

Art.-no. 0630942640

Prices for customers after login

Quantity

x 1 pcs

Exclusively for trade customers

Login/Register
Call customer service: +976 76117940

High-performance core drill bits with 55-mm cutting depth, AlCrN-multilayer coating and 8% cobalt alloy for high service life and versatile use with almost all materials such as in conventional steels, cast iron, titanium, stainless steels, heat-resistant and high-strength steels up to 1400 N/mm² in strength. Also suitable for non-ferrous metals, such as aluminium, aluminium alloys, magnesium alloys, brass, bronze and plastics.

Outstanding performance compared to similar uncoated core drill bits

Significantly higher service life

Up to 60% greater cutting speed

Considerably faster drilling progress

AlCrN multilayer wear-protection coating and 8% cobalt alloy

Extremely high temperature resistance of up to 1050°C

Very high coating hardness of 3000 HV

Multilayer construction for optimum chip removal and improved cutting properties (prevents material wear)

For process reliability in almost all materials

Exact guidance, no slippage

Problem-free drilling on curved surfaces and pipes

No predrilling required, no formation of burrs

Eliminates need for pre- and post-machining

Notice

Unlike the twist drill, the core drill bit does not machine the entire bore diameter, but rather only a thin material ring. The drill core is ejected by an ejector pin using spring tension; this is not included in the scope of delivery. The drilling times of core drill bits are therefore up to ten times shorter than those of twist drills.

Sufficient continuous cooling during the entire drilling process considerably increases the service life of the core drill. Do not use in a dry state.

See the overview tables for core drill bits/material assignments as well as cutting values

Wear appropriate protective equipment when using the sanding tip, such as Eye protection, hearing protection, protective gloves

Set aside loose clothing or jewellery that could get caught in moving parts

The core drill bits must not be used manually

Before use, please ensure that the tool rotates properly and that the clamping function on the tool drive works correctly

Application area

Product information

Würth Catalogue

Datasheets(X)

Certificates/ Documents

Application area

With Weldon shank ∅ 19 mm for use on mobile magnetic drills or stationary drills for creating large holes up to 50 mm in diameter and a cutting depth of max. 55 mm

Fein drills with QuickIn mount can be used with an adapter

Application on stationary drills with Morse taper is possible using the appropriate mount holder

Instructions

Insert the ejector pin into the core drill bit

Push the core drill bit into the mount holder of the drill unit and tighten the hexagon socket screws

The core drill bit is automatically locked into place when using quick-action mounts

Make sure the core drill bit is sitting cleanly in the mount

Putting the drill under lateral load during use may cause the tool to break

Fix the drill unit into the right position for drilling — make sure the drill unit has a stable footing

If necessary, secure the drill unit before drilling using a safety strap, especially for use on vertical surfaces and overhead work

Pay attention to the speed table and use coolant

Drill carefully (without centre punching and pre-drilling), pay attention to an even feed and even rotation speed throughout the entire drilling process

Remove chips and drill core after each drilling operation

Caution: Risk of injury, chips and drill core may be very hot and sharp

Quality	ZEBRA-Premium
Cutting depth	55 mm
Diameter	40 mm
Length	84.6 mm
Material to be processed	Steel Stainless steel Cast metal Non-ferrous metal Hard and tough material
Shank style	Weldon
Surface	AlCrN
Cutting material	HSCo8
Service life (points system)	4 of 4 points
Drilling speed (point system)	4 of 4 points
Bore hole quality (point system)	4 of 4 points
Versatility (points system)	4 of 4 points
Drilling behaviour (point system)	4 of 4 points
Type	Longlife

Cutting values
For dia. 12.0-20.0
Material designation	Tensile strength			from dia. 12.0		from dia. 16.0		from dia. 20.0
		v_c		n		n		n
		from	to	from	to	from	to	from	to
Steels
General structural steels	≤ 850 N/mm²	20	25	531	663	398	497	318	398
Unalloyed quenched and tempered steels	≤ 850 N/mm²	20	25	531	663	398	497	318	398
Low-alloy quenched and tempered steels	≤ 850 N/mm²	20	25	531	663	398	497	318	398
Unalloyed quenched and tempered steels	≤ 1,000 N/mm²	10	15	265	398	199	298	159	239
Low-alloy quenched and tempered steels	≤ 1,000 N/mm²	10	15	265	398	199	298	159	239
Alloyed quenched and tempered steels	≤ 1,300	8	10	212	265	159	199	127	159
Nitriding steels	≤ 1,300	8	10	212	265	159	199	127	159
Tool steels	≤ 1,300	8	10	212	265	159	199	127	159
High-speed steels	≤ 1,300	8	10	212	265	159	199	127	159
High-grade steels
Stainless steels	≤ 1,200	10	15	265	398	199	298	159	239
Titanium	≤ 850	10	15	265	398	199	298	159	239
Special alloys	≤ 1,200	10	15	265	398	199	298	159	239
Cast metals
Cast iron	≤ 350 HB	20	25	531	663	398	497	318	398
Spheroidal graphite and malleable iron	≤ 350 HB	20	25	531	663	398	497	318	398
Non-ferrous metals
Aluminium	≤ 450	20	25	531	663	398	497	318	398
Aluminium alloys	≤ 450	20	25	531	663	398	497	318	398
Aluminium wrought alloys	≤ 400	20	25	531	663	398	497	318	398
Aluminium cast alloys <= 10 % Si	≤ 600	20	25	531	663	398	497	318	398
Aluminium cast alloys >10 % Si	≤ 600	20	25	531	663	398	497	318	398
Magnesium alloys	≤ 400	20	25	531	663	398	497	318	398
Low-alloy copper	≤ 400	20	25	531	663	398	497	318	398
Short-chipping brass	≤ 850	20	25	398	531	298	398	239	318
Long-chipping brass	≤ 850	20	25	398	531	298	398	239	318
Short-chipping bronze	≤ 850	20	25	398	531	298	398	239	318
Long-chipping bronze	≤ 1,000	20	25	531	663	398	497	318	398
Plastics
Thermosetting plastics		20	25	531	663	398	497	318	398
Thermoplastic plastics		20	25	531	663	398	497	318	398

For dia. 24.0-32.0
Material designation	Tensile strength			from dia. 24.0		from dia. 28.0		from dia. 32.0
		v_c		n		n		n
		from	to	from	to	from	to	from	to
Steels
General structural steels	≤ 850 N/mm²	20	25	265	332	227	284	199	249
Unalloyed quenched and tempered steels	≤ 850 N/mm²	20	25	265	332	227	284	199	249
Low-alloy quenched and tempered steels	≤ 850 N/mm²	20	25	265	332	227	284	199	249
Unalloyed quenched and tempered steels	≤ 1,000 N/mm²	10	15	133	199	114	171	99	149
Low-alloy quenched and tempered steels	≤ 1,000 N/mm²	10	15	133	199	114	171	99	149
Alloyed quenched and tempered steels	≤ 1,300	8	10	106	133	91	114	80	99
Nitriding steels	≤ 1,300	8	10	106	133	91	114	80	99
Tool steels	≤ 1,300	8	10	106	133	91	114	80	99
High-speed steels	≤ 1,300	8	10	106	133	91	114	80	99
High-grade steels
Stainless steels	≤ 1,200	10	15	133	199	114	171	99	149
Titanium	≤ 850	10	15	133	199	114	171	99	149
Special alloys	≤ 1,200	10	15	133	199	114	171	99	149
Cast metals
Cast iron	≤ 350 HB	20	25	265	332	227	284	199	249
Spheroidal graphite and malleable iron	≤ 350 HB	20	25	265	332	227	284	199	249
Non-ferrous metals
Aluminium	≤ 450	20	25	265	332	227	284	199	249
Aluminium alloys	≤ 450	20	25	265	332	227	284	199	249
Aluminium wrought alloys	≤ 400	20	25	265	332	227	284	199	249
Aluminium cast alloys <= 10 % Si	≤ 600	20	25	265	332	227	284	199	249
Aluminium cast alloys >10 % Si	≤ 600	20	25	265	332	227	284	199	249
Magnesium alloys	≤ 400	20	25	265	332	227	284	199	249
Low-alloy copper	≤ 400	20	25	265	332	227	284	199	249
Short-chipping brass	≤ 850	20	25	199	265	171	227	149	199
Long-chipping brass	≤ 850	20	25	199	265	171	227	149	199
Short-chipping bronze	≤ 850	20	25	199	265	171	227	149	199
Long-chipping bronze	≤ 1,000	20	25	265	332	227	284	199	249
Plastics
Thermosetting plastics		20	25	265	332	227	284	199	249
Thermoplastic plastics		20	25	265	332	227	284	199	249

For dia. 36.0-50.0
Material designation	Tensile strength			from dia. 36.0		from dia. 40.0		from dia. 50.0
		v_c		n		n		n
		from	to	from	to	from	to	from	to
Steels
General structural steels	≤ 850 N/mm²	20	25	177	221	159	199	127	159
Unalloyed quenched and tempered steels	≤ 850 N/mm²	20	25	177	221	159	199	127	159
Low-alloy quenched and tempered steels	≤ 850 N/mm²	20	25	177	221	159	199	127	159
Unalloyed quenched and tempered steels	≤ 1,000 N/mm²	10	15	88	133	80	119	64	95
Low-alloy quenched and tempered steels	≤ 1,000 N/mm²	10	15	88	133	80	119	64	95
Alloyed quenched and tempered steels	≤ 1,300	8	10	71	88	64	80	51	64
Nitriding steels	≤ 1,300	8	10	71	88	64	80	51	64
Tool steels	≤ 1,300	8	10	71	88	64	80	51	64
High-speed steels	≤ 1,300	8	10	71	88	64	80	51	64
High-grade steels
Stainless steels	≤ 1,200	10	15	88	133	80	119	64	95
Titanium	≤ 850	10	15	88	133	80	119	64	95
Special alloys	≤ 1,200	10	15	88	133	80	119	64	95
Cast metals
Cast iron	≤ 350 HB	20	25	177	221	159	199	127	159
Spheroidal graphite and malleable iron	≤ 350 HB	20	25	177	221	159	199	127	159
Non-ferrous metals
Aluminium	≤ 450	20	25	177	221	159	199	127	159
Aluminium alloys	≤ 450	20	25	177	221	159	199	127	159
Aluminium wrought alloys	≤ 400	20	25	177	221	159	199	127	159
Aluminium cast alloys <= 10 % Si	≤ 600	20	25	177	221	159	199	127	159
Aluminium cast alloys >10 % Si	≤ 600	20	25	177	221	159	199	127	159
Magnesium alloys	≤ 400	20	25	177	221	159	199	127	159
Low-alloy copper	≤ 400	20	25	177	221	159	199	127	159
Short-chipping brass	≤ 850	20	25	133	177	119	159	95	127
Long-chipping brass	≤ 850	20	25	133	177	119	159	95	127
Short-chipping bronze	≤ 850	20	25	133	177	119	159	95	127
Long-chipping bronze	≤ 1,000	20	25	177	221	159	199	127	159
Plastics
Thermosetting plastics		20	25	177	221	159	199	127	159
Thermoplastic plastics		20	25	177	221	159	199	127	159

Key
v_c = cutting speed [m/min]
n = rotation speed [rpm]
The suggested cutting values are reference values and must be adapted to the respective conditions.

Required accessory:

Product

Description

Quantity

Price
/PU

Ejector pin For metal annular cutters

EJCTRPIN-CREDRL-F.0630940XXX

Art.-no. 0630940001

x 1 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).